Saturday, October 17, 2009

Guitar construction and components

General

Guitars can be constructed to meet the demands of both left and right-handed players. Traditionally the dominant hand is assigned the task of plucking or strumming the strings. For the majority of people this entails using the right hand. This is because musical expression (dynamics, tonal expression and colour etc) is largely determined by the plucking hand, while the fretting hand is assigned the lesser mechanical task of depressing and gripping the strings. This is similar to the convention of the violin family of instruments where the right hand controls the bow. A minority, however, believe that left-handed people should learn to play guitars strung in the manner used by right-handed people, simply to standardise the instrument.

Headstock

The headstock is located at the end of the guitar neck furthest from the body. It is fitted with machine heads that adjust the tension of the strings, which in turn affects the pitch. Traditional tuner layout is "3+3" in which each side of the headstock has three tuners (such as on Gibson Les Pauls). In this layout, the headstocks are commonly symmetrical. Many guitars feature other layouts as well, including six-in-line (featured on Fender Stratocasters) tuners or even "4+2" (Ernie Ball Music Man). However, some guitars (such as Steinbergers) do not have headstocks at all, in which case the tuning machines are located elsewhere, either on the body or the bridge.

Nut
The nut is a small strip of bone, plastic, brass, corian, graphite, stainless steel, or other medium-hard material, at the joint where the headstock meets the fretboard. Its grooves guide the strings onto the fretboard, giving consistent lateral string placement. It is one of the endpoints of the strings' vibrating length. It must be accurately cut, or it can contribute to tuning problems due to string slippage, and/or string buzz.


Fretboard
Also called the fingerboard, the fretboard is a piece of wood embedded with metal frets that comprises the top of the neck. It is flat on classical guitars and slightly curved crosswise on acoustic and electric guitars. The curvature of the fretboard is measured by the fretboard radius, which is the radius of a hypothetical circle of which the fretboard's surface constitutes a segment. The smaller the fretboard radius, the more noticeably curved the fretboard is. Most modern guitars feature a 12" neck radius, while older guitars from the 1960s and 1970s usually feature a 6-8" neck radius. Pinching a string against the fretboard effectively shortens the vibrating length of the string, producing a higher pitch. Fretboards are most commonly made of rosewood, ebony, maple, and sometimes manufactured or composite materials such as HPL or resin. See below on section "Neck" for the importance of the length of the fretboard in connection to other dimensions of the guitar.

Frets

Frets are metal strips (usually nickel alloy or stainless steel) embedded along the fretboard and located at exact points that divide the scale length in accordance with a specific mathematical formula. Pressing a string against a fret determines the strings' vibrating length and therefore its resultant pitch. The pitch of each consecutive fret is defined at a half-step interval on the chromatic scale. Standard classical guitars have 19 frets and electric guitars between 21 to 24 frets (though Ibanez has issued guitars with as many as 36 frets.)

Frets are laid out to a mathematical ratio that results in equal tempered division of the octave. The ratio of the spacing of two consecutive frets is the twelfth root of two. The twelfth fret divides the scale length in two exact halves and the 24th fret position divides the scale length in half yet again. Every twelve frets represents one octave. In practice, luthiers determine fret positions using the constant 17.817, which is derived from the twelfth root of two (21/12). The scale length divided by this value yields the distance from the nut to the first fret. That distance is subtracted from the scale length and the result is divided in two sections by the constant to yield the distance from the first fret to the second fret. Positions for the remainder of the frets are calculated in like manner. Actual fret spacing does not use this exact value; the fret spacing on the fretboard was also done by trial and error (testing) method over the ages.

There are several different fret gauges, which can be fitted according to player preference. Among these are "jumbo" frets, which have much thicker gauge, allowing for use of a slight vibrato technique from pushing the string down harder and softer. "Scalloped" fretboards, where the wood of the fretboard itself is "scooped out" between the frets allows a dramatic vibrato effect. Fine frets, much flatter, allow a very low string-action but require other conditions such as curvature of the neck to be well maintained in order to prevent buzz.

On steel-string guitars, frets are eventually bound to wear down; when this happens, frets can be replaced or, to a certain extent, leveled, polished, recrowned, or reshaped as required.

Truss rod

The truss rod is a metal rod that runs along the inside of the neck. It is used to correct changes to the neck's curvature caused by the neck timbers aging, changes in humidity or to compensate for changes in the tension of strings. The tension of the rod and neck assembly is adjusted by a hex nut or an allen-key bolt on the rod, usually located either at the headstock, sometimes under a cover, or just inside the body of the guitar underneath the fretboard and accessible through the sound hole. Some truss rods can only be accessed by removing the neck. The truss rod counteracts the immense amount of tension the strings place on the neck, bringing the neck back to a straighter position. Turning the truss rod clockwise will tighten it, counteracting the tension of the strings and straightening the neck or creating a backward bow. Turning the truss rod counter-clockwise will loosen it, allowing string tension to act on the neck and creating a forward bow. Adjusting the truss rod affects the intonation of a guitar as well as the height of the strings from the fingerboard, called the action. Some truss rod systems, called "double action" truss systems, tighten both ways, allowing the neck to be pushed both forward and backward (standard truss rods can only be released to a point beyond which the neck will no longer be compressed and pulled backward).

Classical guitars do not require truss rods as their nylon strings exert a lower tensile force with lesser potential to cause structural problems. However their necks are often reinforced with a strip of harder wood, such as an ebony strip running down the back of a cedar neck. There is no tension adjustment on this form of reinforcement.

Inlays

Inlays are visual elements set into the exterior surface of a guitar. The typical locations for inlay are on the fretboard, headstock, and on acoustic guitars around the soundhole, known as the rosette. Inlays range from simple plastic dots on the fretboard to intricate works of art covering the entire exterior surface of a guitar (front and back). Some guitar players have used LEDs in the fretboard to produce a unique lighting effects onstage.

Fretboard inlays are most commonly shaped like dots, diamond shapes, parallelograms, or large blocks in between the frets. Dots are usually inlaid into the upper edge of the fretboard in the same positions, small enough to be visible only to the player. These usually appear on the odd numbered frets, but also on the 12th fret (the one octave mark) instead of the 11th and 13th frets. Some older or high-end instruments have inlays made of mother of pearl, abalone, ivory, coloured wood or other exotic materials and designs. Simpler inlays are often made of plastic or painted. High-end classical guitars seldom have fretboard inlays as a well trained player is expected to know his or her way around the instrument.

In addition to fretboard inlay, the headstock and soundhole surround are also frequently inlaid. The manufacturer's logo or a small design is often inlaid into the headstock. Rosette designs vary from simple concentric circles to delicate fretwork mimicking the historic rosette of lutes. Bindings that edge the finger and sound boards are sometimes inlaid. Some instruments have a filler strip running down the length and behind the neck, used for strength and/or to fill the cavity through which the trussrod was installed in the neck.

Elaborate inlays are a decorative feature of many limited edition, high-end and custom-made guitars. Guitar manufacturers often release such guitars to celebrate significant or historic milestones.

Neck
A guitar's frets, fretboard, tuners, headstock, and truss rod, all attached to a long wooden extension, collectively constitute its neck. The wood used to make the fretboard will usually differ from the wood in the rest of the neck. The bending stress on the neck is considerable, particularly when heavier gauge strings are used (see Tuning), and the ability of the neck to resist bending (see Truss rod) is important to the guitar's ability to hold a constant pitch during tuning or when strings are fretted. The rigidity of the neck with respect to the body of the guitar is one determinant of a good instrument versus a poor one. The shape of the neck can also vary, from a gentle "C" curve to a more pronounced "V" curve. There are many different types of neck profiles available, giving the guitarist many options. Some aspects to consider in a guitar neck may be the overall width of the fingerboard, scale (distance between the frets), the neck wood, the type of neck construction (for example, the neck may be glued in or bolted on), and the shape (profile) of the back of the neck. Other type of material used to make guitar necks are graphite (Steinberger guitars), aluminium (Kramer Guitars, Travis Bean and Veleno guitars), or carbon fiber (Modulus Guitars and ThreeGuitars).

Double neck electric guitars have two necks, allowing the musician to quickly switch between guitar sounds.

Neck joint or 'Heel'

This is the point at which the neck is either bolted or glued to the body of the guitar. Almost all acoustic guitars, with the primary exception of Taylors, have glued (otherwise known as set) necks, while electric guitars are constructed using both types.

Commonly used set neck joints include mortise and tenon joints (such as those used by CF Martin & Co. guitars), dovetail joints (also used by CF Martin on the D28 and similar models) and Spanish heel neck joints which are named after the shoe they resemble and commonly found in classical guitars. All three types offer stability. Bolt-on necks, though they are historically associated with cheaper instruments, do offer greater flexibility in the guitar's set-up, and allow easier access for neck joint maintenance and repairs.

Another type of neck, only available for solid body electric guitars, is the neck-through-body construction. These are designed so that everything from the machine heads down to the bridge are located on the same piece of wood. The sides (also known as wings) of the guitar are then glued to this central piece. Some luthiers prefer this method of construction as they claim it allows better sustain of each note. Some instruments may not have a neck joint at all, having the neck and sides built as one piece and the body built around it.

Strings
Modern guitar strings are constructed of metal, polymers, or animal or plant product materials.
Instruments utilising "steel" strings may have strings made of alloys incorporating steel, nickel or phosphor bronze. Classical and flamenco instruments historically used gut strings, but these have been superseded by polymer materials, such as nylon and fluorocarbon materials. Bass strings for both instruments are wound rather than monofilament.

Body (acoustic guitar)

In acoustic guitars, string vibration is transmitted through the bridge and saddle to the body via sound board. The sound board is typically made of tone woods such as spruce or cedar. Timbers for tone woods are chosen for both strength and ability to transfer mechanical energy from the strings to the air within the guitar body. Sound is further shaped by the characteristics of the guitar body's resonant cavity.

In electric guitars, transducers known as pickups convert string vibration to an electric signal, which in turn is amplified and fed to speakers, which vibrate the air to produce the sounds we hear. Nevertheless, the body of the electric guitar still performs a role in shaping the resultant tonal signature.

In an acoustic instrument, the body of the guitar is a major determinant of the overall sound quality. The guitar top, or soundboard, is a finely crafted and engineered element made of tonewoods such as spruce and red cedar. This thin piece of wood, often only 2 or 3 mm thick, is strengthened by differing types of internal bracing. The top is considered by many luthiers to be the dominant factor in determining the sound quality. The majority of the instrument's sound is heard through the vibration of the guitar top as the energy of the vibrating strings is transferred to it.
Body size, shape and style has changed over time. 19th century guitars, now known as salon guitars, were smaller than modern instruments. Differing patterns of internal bracing have been used over time by luthiers. Torres, Hauser, Ramirez, Fleta, and C.F. Martin were among the most influential designers of their time. Bracing not only strengthens the top against potential collapse due to the stress exerted by the tensioned strings, but also affects the resonance characteristics of the top. The back and sides are made out of a variety of timbers such as mahogany, Indian rosewood and highly regarded Brazilian rosewood (Dalbergia nigra). Each one is primarily chosen for their aesthetic effect and can be decorated with inlays and purfling.

The body of an acoustic guitar has a sound hole through which sound is projected. The sound hole is usually a round hole in the top of the guitar under the strings. Air inside the body vibrates as the guitar top and body is vibrated by the strings, and the response of the air cavity at different frequencies is characterised, like the rest of the guitar body, by a number of resonance modes at which it responds more strongly.

Instruments with larger areas for the guitar top were introduced by Martin in an attempt to create louder volume levels. The popularity of the larger "dreadnought" body size amongst acoustic performers is related to the greater sound volume produced.

Body (electric guitar)

Most electric guitar bodies are made of wood and include a plastic pick guard. Boards wide enough to use as a solid body are very expensive due to the worldwide depletion of hardwood stock since the 70's, so the wood is rarely one solid piece. Most bodies are made of two pieces of wood with some of them including a seam running down the centre line of the body. The most common woods used for electric guitar body construction include maple, basswood, ash, poplar, alder, and mahogany. Many bodies will consist of good sounding but inexpensive woods, like ash, with a "top", or thin layer of another, more attractive wood (such as maple with a natural "flame" pattern) glued to the top of the basic wood. Guitars constructed like this are often called "flame tops". The body is usually carved or routed to accept the other elements, such as the bridge, pickup, neck, and other electronic components. Most electrics have a polyurethane or nitrocellulose lacquer finish. Other alternative materials to wood, are used in guitar body construction. Some of these include carbon composites, plastic material (such as polycarbonate) and aluminium alloys.

Pickups

Pickups are transducers attached to a guitar that detect (or "pick up") string vibrations and convert the mechanical energy of the string into electrical energy. The resultant electrical signal can then be electronically amplified. The most common type of pickup is electromagnetic in design. These contain magnets that are tightly wrapped in a coil, or coils, of copper wire. Such pickups are usually placed right underneath the guitar strings. Electromagnetic pickups work on the same principles and in a similar manner to an electrical generator. The vibration of the strings causes a small voltage to be created in the coils surrounding the magnets; this signal voltage is later amplified.

Traditional electromagnetic pickups are either single-coil or double-coil. Single-coil pickups are susceptible to noise induced from electric fields, usually mains-frequency (60 or 50 hertz) hum. The introduction of the double-coil humbucker in the mid-1950s did away with this problem through the use of two coils, one of which is wired in a reverse polarity orientation.

The types and models of pickups used can greatly affect the tone of the guitar. Typically, humbuckers, which are two magnet–coil assemblies attached to each other are traditionally associated with a heavier sound. Single-coil pickups, one magnet wrapped in copper wire, are used by guitarists seeking a brighter, twangier sound with greater dynamic range.

Modern pickups are tailored to the sound desired. A commonly applied approximation used in selection of a pickup is that less wire (lower DC resistance) = brighter sound, more wire = "fat" tone. Other options include specialized switching that produces coil-splitting, in/out of phase and other effects. Guitar circuits are either active, needing a battery to power their circuit, or, as in most cases, equipped with a passive circuit.

Fender Stratocaster type guitars generally utilize three single-coil pickups, while most Gibson Les Paul types use humbucker pickups.

Piezoelectric, or piezo, pickups represent another class of pickup. These employ piezoelectricity to generate the musical signal and are popular in hybrid electro-acoustic guitars. A crystal is located under each string, usually in the saddle. When the string vibrates, the shape of the crystal is distorted, and the stresses associated with this change produce tiny voltages across the crystal that can be amplified and manipulated.

Some piezo-equipped guitars use what is known as a hexaphonic pickup. "Hex" is a prefix meaning six. In a hexaphonic pickup separate outputs are obtained from discrete piezoelectric pickups for each of the six strings. This arrangement allows the signal to be easily modified by on-board modelling electronics, as in the Line 6 Variax brand of electric guitars; the guitars allow for a variety of different sounds to be obtained by digitally manipulating the signal. This allows a guitar to mimic many vintage models of guitar, as well as output alternate tunings without the need to adjust the strings.

Another use for hexaphonic pickups is to send the output signals to a MIDI interpretation device, which determines the note pitch, duration, attack and decay characteristics and so forth. The MIDI (Musical Instrument Digital Interface) interpreter then sends the note information to a sound bank device. The resulting sound can closely mimic numerous types of instruments.

Electronics

On guitars that have them, these components and the wires that connect them allow the player to control some aspects of the sound like volume or tone. These at their simplest consist of passive components such as potentiometers and capacitors, but may also include specialized integrated circuits or other active components requiring batteries for power, for preamplification and signal processing, or even for assistance in tuning. In many cases the electronics have some sort of shielding to prevent pickup of external interference and noise.

Lining, Binding, and Purfling

The top, back and ribs of an acoustic guitar body are very thin (1-2 mm), so a flexible piece of wood called lining is glued into the corners where the rib meets the top and back. This interior reinforcement provides 5 to 20 mm of solid gluing area for these corner joints. Solid linings are often used in classical guitars, while kerfed lining is most often found in steel string acoustics. Kerfed lining is also called kerfing (because it is scored, or kerfed to allow it to bend with the shape of the rib).

During final construction, a small section of the outside corners is carved or routed out and then filled with binding material on the outside corners and decorative strips of material next to the binding, which are called purfling. This binding serves to seal off the endgrain of the top and back. Purfling can also appear on the back of an acoustic guitar, marking the edge joints of the two or three sections of the back.

Binding and purfling materials are generally made of either wood or plastic.

Bridge

The main purpose of the bridge on an acoustic guitar is to transfer the vibration from the strings to the soundboard, which vibrates the air inside of the guitar, thereby amplifying the sound produced by the strings.

On both electric and acoustic guitars, the bridge holds the strings in place on the body. There are many varied bridge designs. There may be some mechanism for raising or lowering the bridge to adjust the distance between the strings and the fretboard (action), and/or fine-tuning the intonation of the instrument. Some are spring-loaded and feature a "whammy bar", a removable arm which allows the player to modulate the pitch moving the bridge up and down. The whammy bar is sometimes also referred to as a "tremolo bar" (see Tremolo for further discussion of this term – the effect of rapidly changing pitch produced by a whammy bar is more correctly called "vibrato"). Some bridges also allow for alternate tunings at the touch of a button.

On almost all modern electric guitars, the bridge is adjustable for each string so that intonation stays correct up and down the neck. If the open string is in tune but sharp or flat when frets are pressed, the bridge can be adjusted with a screwdriver or hex key to remedy the problem. In general, flat notes are corrected by moving the bridge forward and sharp notes by moving it backwards. On an instrument correctly adjusted for intonation, the actual length of each string from the nut to the bridge saddle will be slightly but measurably longer than the scale length of the instrument. This additional length is called compensation, which flattens all notes a bit to compensate for the sharping of all fretted notes caused by stretching the string during fretting.

Pickguard

Also known as a scratchplate. This is usually a piece of laminated plastic or other material that protects the finish of the top of the guitar from damage due to the use of a plectrum or fingernails. Electric guitars sometimes mount pickups and electronics on the pickguard. It is a common feature on steel-string acoustic guitars. Vigorous performance styles such as flamenco, which can involve the use of the guitar as a percussion instrument, call for a scratchplate to be fitted to nylon-string instruments.

Tremolo arm

Many electric guitars are fitted with a vibrato and pitch bend device known as a "tremolo bar (or arm)", "sissy bar", "wang bar", "slam handle", "whammy handle", and "whammy bar". The latter two terms led stompbox manufacturers to use the term 'whammy' in coming up with a pitch raising effect introduced by popular guitar effects pedal brand "Digitech".

The tremolo arm is common enough that there is a technical term, hard tail, for a guitar without one.

Leo Fender, who did much to create the electric guitar, also created much confusion over the meaning of the terms "tremolo" and "vibrato" by the naming the "tremolo" unit on many of his guitars and also the "vibrato" unit on his "Vibrolux" amps. In general, vibrato is a variation in pitch, whereas tremolo is a variation in volume, so the tremolo bar is actually a vibrato bar and the "Vibrolux" amps actually had a tremolo effect. However, following Fender's example, electric guitarists traditionally reverse these meanings when speaking of hardware devices and the effects they produce. See vibrato unit for a more detailed discussion, and tremolo arm for more of the history.

Another type of pitch bender is the B-Bender, a spring and lever device mounted in an internal cavity of a solid body electric, guitar that allows the guitarist to bend just the B string of the guitar using a lever connected to the strap handle of the guitar. The resulting pitch bend is evocative of the sound of the pedal steel guitar.

Guitar Strap

Strip of fabric with a leather or synthetic leather piece on each end. Made to hold a guitar via the shoulders, at an adjustable length to suit the position favoured by the guitarist.

Self-tuning guitars

Self-tuning guitars are computerized guitars programmed to tune themselves. The Gibson Robot guitar, released in 2007, is often mistaken as the first of this kind, but was preceded by the Transperformance system by at least 20 years. Gibson is currently working on a new self-tuning model called the Dark Fire.

Che's Letter To His Parents

Dear old folks:
                   
                        Once again I feel beneath my heels the ribs of Rocinante*. Once more, I'm on the road with my shield on my arm. Almost ten years ago I wrote you another farewell letter. As I recall, I lamented not being a better soilder and a better doctor. The latter no longer interests me; I am not such a bad soilder. Nothing has changed in essence, except that I am much more consious.


My Marxism has taken root and become purified. I believe in armed struggle as the only solution for those peoples who fight to free themselves, and I am consistent with my beliefs. Many will call me an adventurer, and that I am....only one of a different sort: one who risks his skin to prove his truths. It is possible that this may be the end. I don't seek it, but it's within the logical relms of probailities. If it should be so, I send you a final embrace. I have loved you very much, only I have not known how to express my affection. I am extremly rigid in my actions, and I think that sometimes you did not understand me. Nevertheless, please believe me today.

Now a willpower that I have polished with an artist's delight will sustain some shaky legs and some weary lungs. I will do it. Give a thought once in awhile to this little soilder of fortune of the twentieth century.

A kiss to Celia, to Roberto, Juán Martín and Patotín, to Beatriz, to everybody. For you, a big hug from your obstinate and prodigal son,

                                         Ernesto


*Rocinante was Don Quixote's horse.

Che Guevara's letter to Children

If one day you must read this letter, it will be because I am no longer among you. You will almost not remember me and the littlest ones will remember nothing at all. Your father has been a man who acted according to his beliefs and certainly has been faithful to his convictions.


Grow up as good revolutionaries. Study hard to be able to dominate the techniques that permit the domination of nature. Remember that the Revolution is what is important and that each of us, on our own, is worthless.

Above all, try always to be able to feel deeply any injustice committed against any person in any part of the world. It is the most beautiful quality of a revolutionary.

Until always, little children. I still hope to see you again. A really big kiss and a hug from Papa

CHE

Guitar

The guitar is a musical instrument with ancient roots that is used in a wide variety of musical styles. It typically has six strings, but four, seven, eight, ten, eleven, twelve, thirteen and eighteen string guitars also exist.

Guitars are recognized as one of the primary instruments in flamenco, jazz, blues, country, mariachi, rock music, and many forms of pop. They can also be a solo classical instrument. Guitars may be played acoustically, where the tone is produced by vibration of the strings and modulated by the hollow body, or they may rely on an amplifier that can electronically manipulate tone. Such electric guitars were introduced in the 1930s and continue to have a profound influence on popular culture.

Traditionally guitars have usually been constructed of combinations of various woods and strung with animal gut, or more recently, with either nylon or steel strings. Guitars are made and repaired by luthiers. There are many brands of guitars, but some commonly known brands are PRS, Gibson, Dean, Gretsch, Ibanez, Martin, Jackson, Schecter, and Fender.



History



Before the development of the electric guitar and the use of synthetic materials, a guitar was defined as being an instrument having "a long, fretted neck, flat wooden soundboard, ribs, and a flat back, most often with incurved sides". Instruments similar to the guitar have been popular for at least 4,000 years. While today's classical guitar first appeared in Spain, it was itself a product of the long and complex history that saw a number of related guitar types developed and used across Europe. The roots of the guitar can be traced back thousands of years to an Indo-European origin in instruments, then known in central Asia and India. For this reason the guitar itself is distantly related to instruments such as the tanbur and setar, and the Indian sitar. The oldest known iconographic representation of an instrument displaying all the essential features of a guitar being played is a 3,300 year old stone carving of a Hittite bard. The modern word, guitar, was adopted into English from Spanish guitarra (German Gitarre, French Guitare), loaned from the medieval Andalusian Arabic qitara, itself derived from the Latin cithara, which in turn came from the earlier Greek word kithara, a possible descendant of Old Persian sihtar.

Illustration from a Carolingian Psalter from the 9th century, showing a guitar-like plucked instrument.

The modern guitar is descended from the Roman cithara brought by the Romans to Hispania around 40 AD, and further adapted and developed with the arrival of the four-string oud, brought by the Moors after their conquest of the Iberian peninsula in the 8th century. Elsewhere in Europe, the indigenous six-string Scandinavian lut (lute), had gained in popularity in areas of Viking incursions across the continent. Often depicted in carvings c. 800 AD, the Norse hero Gunther (also known as Gunnar), played a lute with his toes as he lay dying in a snake-pit, in the legend of Siegfried. By 1200 AD, the four string "guitar" had evolved into two types: the guitarra morisca (Moorish guitar) which had a rounded back, wide fingerboard and several soundholes, and the guitarra latina (Latin guitar) which resembled the modern guitar with one soundhole and a narrower neck.

The Spanish vihuela or "viola da mano", a guitar-like instrument of the 15th and 16th centuries is, due to its similarities, is often considered an important influence in the development of the modern guitar. It had lute-style tuning and a guitar-like body. Its construction had as much in common with the modern guitar as with its contemporary four-course renaissance guitar. The vihuela enjoyed only a short period of popularity; the last surviving publication of music for the instrument appeared in 1576. It is not clear whether it represented a transitional form or was simply a design that combined features of the Arabic oud and the European lute. In favor of the latter view, the reshaping of the vihuela into a guitar-like form can be seen as a strategy of differentiating the European lute visually from the Moorish oud. Meanwhile, the five string renassance guitar and the baroque guitar enjoyed popularity, especially in Italy and France, and indeed, much of Europe from the 15th to the 18th centuries.

The Vinaccia family of luthiers is known for developing the mandolin, and may have built the oldest surviving six string guitar. Gaetano Vinaccia (1759 – after 1831) has his signature on the label of a guitar built in Naples, Italy for six strings with the date of 1779. This guitar has been examined and does not show tell-tale signs of modifications from a double-course guitar although fakes are known to exist of guitars and identifying labels from that period.

The dimensions of the modern classical guitar (also known as the Spanish guitar) were established by Antonio Torres Jurado (1817-1892), working in Seville in the 1850s. Torres and Louis Panormo of London (active 1820s-1840s) were both responsible for demonstrating the superiority of fan strutting over transverse table bracing.

Friday, October 16, 2009

Che Guevara's letter to Fidel Castro


Havana, April 1, 1965.
Fidel:
At this moment I remember many things-when I met you in Maria Antonia's house, when you proposed I come along, all the tensions involved in the preparations." One day they came by and asked who should be notified in case of death, and the real possibility of it struck us all. Later we knew it was true, that in a revolution one wins or dies (if it is a real one). Many comrades fell along the way to victory.Today everything has a less dramatic tone, because we are more mature, but the event repeats itself. I feel that I have fulfilled the part of my duty that tied me to the Cuban revolution in its territory, and I say farewell to you, to the comrades, to your people, who now are mine.I formally resign my positions in the leadership of the party, my post as minister, my rank of commander, and my Cuban citizenship. Nothing legal binds me to Cuba. The only ties are of another nature-those that cannot be broken as can appointments to posts.Reviewing my past life, I believe I have worked with sufficient integrity and dedication to consolidate the revolutionary triumph. My only serious failing was not having had more confidence in you from the first moments in the Sierra Maestra, and not having understood quickly enough your qualities as a leader and a revolutionary.I have lived magnificent days, and at your side I felt the pride of belonging to our people in the brilliant yet sad days of the Caribbean crisis." Seldom has a statesman been more brilliant as you were in those days. I am also proud of having followed you without hesitation, of having identified with your way of thinking and of seeing and appraising dangers and principles.Other nations of the world summon my modest efforts of assistance. I can do that which is denied you due to your responsibility at head of Cuba, and the time has come for us to part.You should know that I do so with a mixture of joy and sorrow. I leave here the purest of my hopes as a builder and the dearest of those I hold dear. And I leave a people who received me as a son. That wounds a part of my spirit. I carry to new battlefronts the faith that you taught me, the revolutionary spirit of my people, the feeling of fulfilling the most sacred of duties: to fight against imperialism wherever one may be. This is a source of strength, and more than heals the deepest of wounds.I state once more that I free Cuba from all responsibility, except that which stems from its example. If my final hour finds me under other skies, my last thought will be of this people and especially of you. I am grateful for your teaching and your example, to which I shall try to be faithful up to the final consequences of my acts.I have always been identified with the foreign policy of our revolution, and I continue to be. Wherever I am, I will feel the responsibility of being a Cuban revolutionary, and I shall behave as such. I am not sorry that I leave nothing material to my wife and children; I am happy it is that way. I ask nothing for them, as the state will provide them with enough to live on and receive an education.I would have many things to say to you and to our people, but I feel they are unnecessary. Words cannot express what I would like them to, and there is no point in scribbling pages.
Ever onward to victory!

Homeland or Death!

I embrace you with all my revolutionary fervour.
Che